Avaya-96x1IPTelephone-MIB DEFINITIONS ::= BEGIN IMPORTS enterprises, OBJECT-TYPE, MODULE-IDENTITY, Integer32, IpAddress FROM SNMPv2-SMI DisplayString FROM RFC1213-MIB ; avaya96x1HMIB MODULE-IDENTITY LAST-UPDATED "1608290614Z" --YYMMDDHHMM ORGANIZATION "avaya" CONTACT-INFO "Avaya Customer Services Avaya, Inc. WWW: www.avaya.com" DESCRIPTION "MIB Module for H.323 96x1 IP Telephones as of Release 6.6.3 Copyright 2016 by Avaya Inc. All rights reserved." REVISION "1608290614Z" --YYMMDDHHMM DESCRIPTION " 6.6.3 release: 1. Add endptCLEAR_EXTPSWD_ON_LOGOUT item. 2. Add endptCLBACKUPTIMESTAT item. 3. Add endptCLBACKUPTIME item. 4. Add endptCLDISPCONTENT item. 5. Update endptNVRINGTONESTYLE description. 6.6.2 release: 1. Add endptAUTHCTRLSTAT MIB item. 2. Add new enumerations 10-14 to endptAPPstat. 3. The following MIB items are not applicable for phones with HWVERS 3 and up as conveyed by endptHWVER: endptRFSNAME, endptRFSINUSE, endptRFSstat, endpBOOT1INUSE, endpBOOT2INUSE. 4. Add note that endptAPPINUSE returns the filename of the Application/Library software package if the phone with HWVERS up to 3 (as conveyed by endptHWVER) and returns the firmware version of the active bank if the phone with HWVERS 3 and up (as conveyed by endptHWVER). 5. Add note that endptBACKUPAPP returns the filename of the Backup Application in the phone with HWVERS up to 3 (as conveyed by endptHWVER) and returns the firmware version of the inactive bank if the phone with HWVERS 3 and up. 6. Add endptTLSVERSION MIB item. 7. Add endptCTASTAT and update the description of endptENHDIALSTAT. 8. Add endptH323SIGPROTOCOL MIB item. 6.6 release: 1. Add endptNVMCREGMODE MIB item. 2. Update the description of endptSERVICESTAT for the H.323 signaling and registration over TLS. 3. Add new MIB items for FIPS mode: endptFIPSENABLED and endptFIPSTEST. 4. Mark as obsoleted MIB item endptTLSSRVRID and create new MIB item endptTLSSRVRVERIFYID instead. 5. Add new MIB item for TLS secure rengotiation (RFC 5746): endptTLSSECURERENEG. 6. Add new MIB item for PKCS#12 support: endptPKCS12URL. 7. Add new MIB item for certificate expiration warning: endptCERTWARNINGDAYS. 8. Add new MIB items OCSP: endptOCSPURI, endptOCSPURIPREF, endptOCSPACCEPTUNK, endptOCSPNONCE, endptOCSPTRUSTCERTS, endptOCSPTRUSTLIST. 9. Add new MIB items for checking certificate expiration or revocation for active TLS sessions: endptSERVERCERTRECHECKHOURS. 10. Add new MIB item endptAUDIOLOG. " ::= { ipEndpointMIBs 5 } avaya OBJECT IDENTIFIER ::= { enterprises 6889 } products OBJECT IDENTIFIER ::= { avaya 1 } mibs OBJECT IDENTIFIER ::= { avaya 2 } avayaipEndpointProd OBJECT IDENTIFIER ::= { products 69 } ipEndpointMIBs OBJECT IDENTIFIER ::= { mibs 69 } avaya96x1H323Endpoints OBJECT IDENTIFIER ::= { avayaipEndpointProd 5 } avaya9608H323 OBJECT IDENTIFIER ::= { avaya96x1H323Endpoints 1 } avaya9611H323 OBJECT IDENTIFIER ::= { avaya96x1H323Endpoints 2 } avaya9621H323 OBJECT IDENTIFIER ::= { avaya96x1H323Endpoints 3 } avaya9641H323 OBJECT IDENTIFIER ::= { avaya96x1H323Endpoints 4 } avayaB189H323Endpoints OBJECT IDENTIFIER ::= { avayaipEndpointProd 8 } avayaB189h323 OBJECT IDENTIFIER ::= { avayaB189H323Endpoints 1 } endptID OBJECT IDENTIFIER ::= { avaya96x1HMIB 1 } endptAGCHAND OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Handset AGC status. This variable returns 1 if the endpoint's handset Automatic Gain Control capability is currently enabled, else 0." ::= { endptID 1 } endptAGCHEAD OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Headset AGC status. This variable returns 1 if the endpoint's headset Automatic Gain Control capability is currently enabled, else 0." ::= { endptID 2 } endptAGCSPKR OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Speakerphone AGC status. This variable returns 1 if the endpoint's speakerphone Automatic Gain Control capability is currently enabled, else 0." ::= { endptID 3 } endptAPPINUSE OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Application package name. This variable returns the name of the application package in the endpoint. Phone with HWVERS up to 3 (as conveyed by endptHWVER) returns the filename of the Application/Library software package. Phone with HWVERS 3 and up (as conveyed by endptHWVER) returns the firmware version of the active b " ::= { endptID 4 } endptAPPNAME OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Application file ID. This variable returns a string specifying the system-specific application file that should be used for telephone operation." ::= { endptID 5 } endptAUDIOENV OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Audio Environment parameter. This variable returns the current value of AUDIOENV." ::= { endptID 6 } endptAUDIOSTHD OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Audio Handset Sidetone parameter. This variable returns the current value of AUDIOSTHD." ::= { endptID 7} endptAUDIOSTHS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Audio Headset Sidetone parameter. This variable returns the current value of AUDIOSTHS." ::= { endptID 8} endptBAKLIGHTOFF OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Backlight idle timer setting. This variable returns the number of minutes of idle time, after which the telephone backlightis turned off. Range is 0-999, with a default of 120. Used in phones with backlit displays." ::= { endptID 9 } endptBACKUPAPP OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Backup application package name. This variable returns a string specifying the name of the application package stored as a backup copy. Phone with HWVERS up to 3 (as conveyed by endptHWVER) returns the filename of the Backup Application. Phone with HWVERS 3 and up (as conveyed by endptHWVER) returns the firmware version of the inactive bank. " ::= { endptID 10 } endptBRAUTH OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Backup/Restore authentication control. This variable returns 0 if the call server IP address and telephone's registration password is NOT not included as credentials in an Authentication request-header; 1 (the default) if that data is included and the telephone will accept the server's digital certificate if signed by Avaya, or 2 if that data is included and the telephone will accept the server's digital certificate if signed by Avaya or a trusted certificate based on TRUSTCERTS." ::= { endptID 11} endptBRURI OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Backup and restore URI. This variable returns a string specifying the URI used for backup and restore files." ::= { endptID 12 } endptCNAPORT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Chatter server port. This variable returns the Chatter server registration transport-layer port number (from 0 to 65535; default is 8888)." ::= { endptID 13 } endptCNASRVR OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS obsolete DESCRIPTION "CNA server addresses. This variable returns zero or more Chatter server addresses for network analysis, in dotted decimal or DNS format." ::= { endptID 14 } endptCODECR OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Receive codec. This variable returns the designation of the Receive codec currently in use." ::= { endptID 15 } endptCODECT OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Transmit codec. This variable returns the designation of the Transmit codec currently in use." ::= { endptID 16 } endptDHCPINUSE OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP address of DHCP server from which phone's IP address was obtained. This variable returns four zeroes by default or when the telephone is manually programmed." ::= { endptID 17 } endptDHCPINUSEV6 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "IP address of DHCPv6 server from which phone's IP address was obtained converted to ASCII colon-hex format. This variable returns two colons by default or when the telephone is manually programmed." ::= { endptID 18 } endptDHCPLEASEEXP OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DHCP lease expiration. This variable returns the time (in seconds) remaining until the expiration of the current DHCP lease; or 0 if the lease has expired." ::= { endptID 19} endptDHCPLEASEREBIND OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Rebind time of IPADD lease. This variable returns an unsigned integer specifying the length of time at which to rebind the IPADD lease, in seconds as received by DHCP option 59 or as computed from the lease time if option 59 is not received." ::= { endptID 20} endptDHCPLEASERENEW OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Renewal time of IPADD lease. This variable returns an unsigned integer specifying the length of time at which to renew the IPADD lease, in seconds as received by DHCP option 58 or as computed from the lease time if option 58 is not received." ::= { endptID 21} endptDHCPLEASETIME OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Duration of IPADD lease. This variable returns an unsigned integer specifying the length of time of the IPADD lease, in seconds as received by DHCP option 51." ::= { endptID 22} endptDHCPPREF OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "DHCP IPv4 or IPv6 preference specification. This variable returns 4 if new values received via DHCPv4 are preferred of DHCPv6 if both are received, and returns 6 if new values received via DHCPv6 are preferred of DHCPv4 if both are received." ::= { endptID 23 } endptDHCPSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "DHCP IPv4 or IPv6 permission specificatio. This variable returns 1 if IPv4 only is to be used, 2 if IPv6 only is to be used, and 3 if either can be used." ::= { endptID 24 } endptDHCPSTD OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "DHCP compliance flag. This variable returns 0 (the default) if the telephone ignores the DHCP standard and continues using its IP address after its lease has expired, assuming the DHCP server cannot be reached. The value 1 is returned if the DHCP standard is followed and the telephone stops using its IP address (IPADD)." ::= { endptID 25 } endptDHCPT1REM OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DHCP lease renewal expiration. This variable returns the time (in seconds) until the start of IP address lease renewal, -1 if the lease is infinite, or 0 if the timer has expired." ::= { endptID 26 } endptDHCPT2REM OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DHCP lease rebinding expiration. This variable returns the time (in seconds) remaining until the start of IP address lease renewal, -1 if the lease is infinite, or 0 if the timer has expired." ::= { endptID 27 } endptDHCPV6LEASEEXP OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DHCPv6 lease expiration. This variable returns the time (in seconds) remaining until the expiration of the current DHCPv6 lease; or 0 if the lease has expired." ::= { endptID 28 } endptDHCPV6LIFEPREF OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DHCPv6 preferred-lifetime value. This variable returns the preferred-lifetime value received in the DHCPv6 IA Address option." ::= { endptID 29 } endptDHCPV6LIFEVALID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DHCPv6 valid-lifetime value. This variable returns the valid-lifetime value received in the DHCPv6 IA Address option." ::= { endptID 30 } endptDHCPV6T1 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "T1 value. This variable returns the T1 value received in the DHCPv6 IA_NA option." ::= { endptID 31 } endptDHCPV6T1REM OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DHCPv6 lease renewal expiration. This variable returns the time (in seconds) until the start of IPv6 address lease renewal, -1 if the lease is infinite, or 0 if the timer has expired." ::= { endptID 32 } endptDHCPV6T2 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "T2 value. This variable returns the T2 value received in the DHCPv6 IA_NA option." ::= { endptID 33 } endptDHCPV6T2REM OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DHCPv6 rebinding renewal expiration. This variable returns the time (in seconds) until the start of IPv6 address lease renewal, -1 if the lease is infinite, or 0 if the timer has expired." ::= { endptID 34 } endptDNSSRVR OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "List of DNS server addresses. This variable returns a sequence of IP addresses, in dotted-decimal format and separated by commas, of DNS servers available for use." ::= { endptID 35 } endptDOMAIN OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "List of DNS domain labels. This variable returns a sequence of labels, separated by periods, for use as the highest-level domain in resolving DNS names in system values." ::= { endptID 36 } endptDOT1X OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current value for 802.1X handling. This variable returns 0 if Supplicant operation is Enabled, 1 if Supplicant operation is Enabled with proxy Logoff, and 2 if Supplicant operation is Disabled. The default is 0." ::= { endptID 37 } endptDOT1XSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "802.1X Supplicant status. This variable returns 0 if 802.1X Supplicant mode is Disabled; 1 (the default) if the supplicant mode is set to Unicast-only, and 2 if the supplicant mode is set to Unicast/Multicast." ::= { endptID 38 } endptDSCPAUD OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "DSCP for audio. This variable specifies the Differentiated Services Code Point for audio currently in use (between 0 and 63 inclusive)." ::= { endptID 39 } endptDSCPBBE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "DSCP BBE priority value. This variable returns an integer between 0 and 7 inclusive specifying the far-end endpoint's DiffServ Better than Best Effort audio priority value." ::= { endptID 40} endptDSCPSIG OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION " DSCP for signaling. This variable specifies the Differentiated Services Code Point for signaling currently in use (between 0 and 63 inclusive)." ::= { endptID 41 } endptDSPVERSION OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "DSP Version. This variable returns a string of up to 10 characters, that identifies the version of the DSP firmware in the endpoint." ::= { endptID 42 } endptFEIPADD OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Far-end Audio endpoint address. This variable returns a dotted-decimal or colon-hex IP address converted to a text string specifying the address of the far-end audio endpoint currently in use." ::= { endptID 43} endptFEPORT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Audio endpoint port number. This variable returns the far-end endpoint's transport layer port number for audio, currently in use." ::= { endptID 44 } endptFONT OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Font file identifier. This variable returns a text string with the name of the font file stored in the phone, if any." ::= { endptID 45 } endptGIPADD OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "List of router addresses. This variable returns a sequence of IP addresses, in dotted-decimal format and separated by commas, of routers available for use." ::= { endptID 46 } endptGIPINUSE OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IPv4 Router address. This variable returns a 4-octet string specifying the IP address of the router currently in use." ::= { endptID 47 } endptGIPINUSEV6 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "IPv6 Router address. This variable returns a colon-hex address specifying the IP address of the router currently in use, converted to a text string." ::= { endptID 48 } endptGRATARP OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Gratuitous ARP permission flag. This variable returns 1 if gratuitous ARPs are allowed to be processed, else 0." ::= { endptID 49 } endptGRATNAV6 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "IPv6 Gratuitous Neighbor Advertisement permission flag. This variable returns 1 if gratuitous IPv6 Neighbor Advertisement messages are allowed to be processed, else 0." ::= { endptID 50 } endptGROUP OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Group identifier. This variable returns the integer corresponding to the current group identifier." ::= { endptID 51 } endptHTTPDIR OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "HTTP server Directory. This variable returns the path used in formation of the URI for HTTP GET operations." ::= { endptID 52 } endptHTTPPORT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "HTTP port number. This variable returns the TCP port number used for HTTP file downloading." ::= { endptID 53 } endptHTTPSRVR OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "HTTP server IP addresses. This variable returns a comma-separated list of HTTP server IP addresses available for use, in dotted-decimal or DNS format." ::= { endptID 54 } endptHTTPUSED OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "HTTP initialization server IP address. This variable returns a 4-octet or colon-hex IP address for the HTTP server used during initialization (all zeroes if no server successfully used during initialization), converted to a text string." ::= { endptID 55 } endptICMPDU OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current value for ICMP Destination message handling. This variable returns 0 if the telephone does not transmit ICMP Destination Unreachable messages are not transmitted; 1 if such messages are transmitted only in response to datagrams that designate closed UDP ports or if the designated transport protocol is not supported, and 2 if such such messages are sent only in response to datagrams that designate closed UDP or TCP ports or if the designated transport protocol is not supported. The default is 1." ::= { endptID 56 } endptICMPRED OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current value for ICMP Redirect message handling. This variable returns 1 if received Redict messages are handled as specified in RFC 1122, Sections 3.2.2.2 and 3.3.1.2, else 0. The default is 0." ::= { endptID 57 } endptIPADD OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Endpoint IPv4 address. This variable returns a 4-octet string specifying the endpoint's current IP address." ::= { endptID 58 } endptIPADDV6 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Endpoint IPv6 address. This variable returns a colon-hex IP address specifying the endpoint's current IP address, converted to a text string." ::= { endptID 59 } endptIPADDV6LL OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Endpoint IPv6 link-local address. This variable returns a colon-hex IP address specifying the endpoint's current linked-local IP address, converted to a text string." ::= { endptID 60 } endptIPPREF OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "DNS IPv4 or IPv6 preference specification. This variable returns 4 if the DNS resolver should list IPv4 addresses before IPv6 addresses, and returns 6 if the DNS resolver should list IPv6 addresses before IPv4 addresses." ::= { endptID 61 } endptIPV6STAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "DHCP IPv4 or IPv6 permission specification. This variable returns 1 if IPv4 only is to be used, 2 if IPv6 only is to be used, and 3 if either can be used." ::= { endptID 62 } endptJMSEC OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Jitter buffer size. This variable returns the number of milliseconds of delay added to compensate for network jitter, from 0-300 milliseconds. The default is 10." ::= { endptID 63 } endptL2Q OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "802.1Q framing flag. This variable returns 0 if the Layer 2 802.1Q framing parameter is set to 'auto', 1 if it is set to on/enabled, else 2 for off/disabled." ::= { endptID 64 } endptL2QAUD OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Audio priority. This variable returns an integer between 0 and 7 inclusive specifying the current Layer 2 802.1Q audio priority value." ::= { endptID 65 } endptL2QSIG OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Signaling priority. This variable returns an integer between 0 and 7 inclusive specifying the current Layer 2 802.1Q signaling priority value." ::= { endptID 66 } endptL2QSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "802.1Q tagging flag. This variable returns 0 if the Layer 2 802.1Q tagging parameter is currently OFF, else 1." ::= { endptID 67 } endptL2QVLAN OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Administered Telephone VLAN Identifier. This variable returns an integer between 0 and 4094 inclusive specifying the administered Layer 2 802.1Q VLAN Identifier value." ::= { endptID 68} endptL2QVLANINUSE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Telephone VLAN Identifier in use. This variable returns an integer between 0 and 4094 inclusive specifying the current Layer 2 802.1Q VLAN Identifier value." ::= { endptID 69 } endptLANGFILES OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Language file list. This variable returns a comma-separated text string listing the language files stored in the phone, if any." ::= { endptID 70 } endptLOGSRVR OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Event Log server address. This variable returns at most one IP address, in dotted-decimal or DNS format, of the server to be used for event logging. This function is intended for Avaya use, in debugging if necessary." ::= { endptID 71 } endptMACADDR OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address. This variable returns a 6-octet string specifying the endpoint's MAC address." ::= { endptID 72 } endptMEMHEAPFREE OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Heap allocation. This variable returns the number of bytes of volatile memory currently allocated for, but unused by, the Heap." ::= { endptID 73 } endptMODEL OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Model identifier. This variable returns a string of up to 8 ASCII characters." ::= { endptID 74 } endptNDREDV6 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "IPv6 Neighbor Discovery Redirect permission flag. This variable returns 1 if IPv6 Neighbor Discovery Redirect messages are to be processed, else 0." ::= { endptID 75 } endptNETMASK OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Subnet mask. This variable returns a 4-octet string specifying the subnet mask currently in use." ::= { endptID 76 } endptPHNEMERGNUM OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Emergency Number. This variable returns a telephone number to be dialed when an Emergency softkey is pressed." ::= { endptID 77 } endptPHONECC OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Phone comcode. This variable returns a string of up to 9 numerical characters, specifying the comcode of the endpoint itself." ::= { endptID 78 } endptPHONESN OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Housing serial number. This variable returns a string of up to 18 ASCII characters, specifying the serial number on the outside of the endpoint's housing." ::= { endptID 79 } endptPHY1DUPLEX OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet line interface duplex setting. This variable returns 1 if the interface is half-duplex and 2 if the interface is full duplex." ::= { endptID 80 } endptPHY1SPEED OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet interface speed. This variable returns a string specifying the endpoint's Ethernet interface speed in Mbps: '1000' or '100' or '10'." ::= { endptID 81 } endptPHY1STAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet line interface status. This variable returns 0 if the endpoint's Ethernet line interface is currently NOT enabled, 1 if the Ethernet line interface is currently for auto-negotiation, 2 for 10Mbps half-duplex, 3 for 10Mbps full-duplex, 4 for 100Mbps half-duplex, and 5 for 100Mbps full-duplex." ::= { endptID 82 } endptPHY2DUPLEX OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Secondary Ethernet interface duplex setting. This variable returns 0 if no link is established, 1 if the interface is half-duplex,and 2 if the interface is full duplex." ::= { endptID 83 } endptPHY2PRIO OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Secondary Ethernet interface Layer 2 priority. This variable returns 0 through 7, and is used with endptVLANSEP. The default is 0." ::= { endptID 84 } endptPHY2SPEED OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Secondary Ethernet speed. This variable returns a string specifying the endpoint's Ethernet interface speed in Mbps: '100' or '10' or '0'." ::= { endptID 85 } endptPHY2STAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Secondary Ethernet interface status. This variable returns 0 if the endpoint's Secondary Ethernet interface is currently NOT enabled, 1 if the Secondary Ethernet interface is currently for auto-negotiation, 2 for 10Mbps half-duplex, 3 for 10Mbps full-duplex, 4 for 100Mbps half-duplex, and 5 for 100Mbps full-duplex." ::= { endptID 86 } endptPHY2VLAN OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Secondary Ethernet interface VLAN ID. This variable returns an integer between 0 and 4094 inclusive specifying the current Layer 2 802.1Q VLAN Identifier value for tagged frames received on the secondary Ethernet interface while VLAN separation is enabled." ::= { endptID 87 } endptPINGREPLYV6 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "ICMPv6 Echo Reply permission flag. This variable returns 0 if the telephone is never to send an ICMPv6 Echo Reply, 1 if the ICMPv6 Echo Reply is sent only in reply to received Echo Request messages with a Destination Address equal to one of the telephone unicast IPv6 addresses, and 2 if the ICMPv6 Echo Reply is sent in reply to received Echo Request messages with a Destination Address equal to one of the telephone unicast, multicast or anycast IPv6 addresses ." ::= { endptID 88 } endptPORTAUD OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Transport-layer audio port. This variable returns the endpoint's transport layer port number for audio, currently in use." ::= { endptID 89 } endptPROCPSWD OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Local Procedure Password. This variable returns 0 if the Local Procedure Password is null, else 1." ::= { endptID 90 } endptPROCSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Local Procedure flag. This variable returns 0 if Local Procedures are currently allowed for this telephone, else 1." ::= { endptID 91 } endptPWBCC OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "PWB comcode. This variable returns a string of up to 9 numerical characters, specifying the comcode or version number of the printed wiring board of the endpoint." ::= { endptID 92 } endptPWBSN OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "PWB serial number. This variable returns a string of up to 18 ASCII characters, specifying the serial number on the endpoint's printed wiring board, or N/A if the board has no serial number." ::= { endptID 93 } endptRFSINUSE OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "In-use RFS package name. This variable returns the name of the Kernel/Root File System package in the endpoint from which the active Kernel/Root File System files were installed. This MIB item is not applicable for phones with HWVERS 3 and up as conveyed by endptHWVER" ::= { endptID 94 } endptRFSNAME OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "RFS package name. This variable returns the name of the file that contains the Kernel/Root File System package for the endpoint. This MIB item is not applicable for phones with HWVERS 3 and up as conveyed by endptHWVER" ::= { endptID 95 } endptRSVPCONT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "RSVP Control flag. This variable returns 0 if the RSVP control status is off/disabled, else 1." ::= { endptID 96 } endptRSVPPROF OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "RSVP profile flag. This variable returns 0 if the RSVP profile is guaranteed, else 1 for controlled load." ::= { endptID 97 } endptRSVPRFRSH OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "RSVP Refresh rate. This variable returns an integer between 1 and 3600 inclusive specifying the RSVP refresh rate in milliseconds." ::= { endptID 98 } endptRSVPRTRY OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "RSVP Failed Retry flag. This variable returns 0 if the RSVP Failed Retry Reservation control status is off/disabled, else 1." ::= { endptID 99 } endptRTCPCONT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "RTCP Control flag. This variable returns 0 if the RTCP control status is off/disabled, else 1." ::= { endptID 100 } endptRTCPFLOW OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "RTCP Flowrate. This variable returns an integer between 5 and 30 inclusive specifying the RTCP flowrate in milliseconds." ::= { endptID 101 } endptRTCPMON OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "RTCP Monitor address. This variable returns a 4-octet or colon-hex IP address of the RTCP monitor currently in use, converted to a text string." ::= { endptID 102 } endptSIG OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Signaling protocol download flag. This variable returns the integer corresponding to the current signaling protocol." ::= { endptID 103 } endptSNMPADD OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "SNMP source addresses. This variable returns one or more allowable source IP addresses for SNMP queries, in dotted decimal or DNS format." ::= { endptID 104 } endptSSONCONTENT OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "SSON Content. This variable returns the data portion of the DHCP site-specific option designated by NVSSON, exactly as received." ::= { endptID 105 } endptSTATIC OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Static programming override flag. This variable returns the integer corresponding to the current level of override permissions for static programming." ::= { endptID 106 } endptTLSDIR OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "TLS Server Directory. This variable returns the path that is prepended to all file names used in HTTPS GET operations." ::= { endptID 107 } endptTLSPORT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "TLS server port number. This variable returns the TCP port number used for HTTPS file downloading." ::= { endptID 108 } endptTLSSRVR OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "TLS server addresses. This variable returns zero or more Transport Layer Security server addresses for software download, in dotted decimal or DNS format." ::= { endptID 109 } endptTLSSRVRID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS obsolete DESCRIPTION "TLS server ID flag. This variable returns 1 if the TLS server identity is to be checked against its certificate, otherwise 0." ::= { endptID 110 } endptTLSUSED OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "TLS server address used. This variable returns the TLS server address from TLSSRVR used, if any, during initialization, or all zeroes if no TLS server was used, in a text string." ::= { endptID 111 } endptTMSEC OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Transmit buffer fill level. This variable returns the transmit buffer minimum fill level, in msec, currently in use." ::= { endptID 112 } endptTRUSTCERTS OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Trusted Certificates list. This variable returns the current trusted certificates to be downloaded; 0-255 ASCII characters, 0 or more filenames or URLs separated by commas." ::= { endptID 113 } endptVLANLIST OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID list. This variable returns a list of zero or more VLAN IDs." ::= { endptID 114 } endptVLANSEP OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN separation value. This variable returns 0 if frames received on the secondary Ethernet interface are unchanged before forwarding; else 1, which is the default." ::= { endptID 115 } endptVOXFILES OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Voice language files list. This variable returns the current list of voice langauge files to be downloaded; 0-255 ASCII characters, 0 or more filenames separated by commas." ::= { endptID 116} endptVSICONTENT OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor-specific option data. This variable returns the contents of the option data portion of vendor-specific option 242, exactly as received in the DHCPv6 Vendor-Specific Information option." ::= { endptID 117 } endptBOOT1INUSE OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Boot1 filename. This variable returns the name of the boot1 file stored in the telephone. This MIB item is not applicable for phones with HWVERS 3 and up as conveyed by endptHWVER." ::= { endptID 118 } endptBOOT2INUSE OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Boot2 filename. This variable returns the name of the boot2 file stored in the telephone. This MIB item is not applicable for phones with HWVERS 3 and up as conveyed by endptHWVER" ::= { endptID 119 } endptAUTOANSSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Auto-answer permission flag. This variable returns 1 if the telephone always auto-answers incoming calls; 2 if it auto-answers all incoming calls on primary call appearances (PCAs), 3 if it auto-answers incoming call but only when logged in as a call center phone, 4 if it auto-answers all incoming calls but only when logged in as a call center phone, else 0, which is the default. Note that AUTOANSSTRING can further restrict the impact of AUTOANSSTAT" ::= { endptID 120 } endptAUTOANSSTRING OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Auto-answer string. This variable returns the text string required to be in the incoming call display message (if any) before the telephone can auto-answer in accordance with AUTOANSSTAT." ::= { endptID 121 } endptLNQ OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item returns the Local Network Quality level. 0 if no local network quality is available, else 6 if packet loss is < 1% and round-trip network delay is < 400 milliseconds and jitter compensation delay is < 80 milliseconds, else 5 if packet loss is < 2% and round-trip network delay is < 425 milliseconds and jitter compensation delay is < 100 milliseconds, else 4 if packet loss is < 3% and round-trip network delay is < 450 milliseconds and jitter compensation delay is < 120 milliseconds, else 3 if packet loss is < 4% and round-trip network delay is < 475 milliseconds and jitter compensation delay is < 160 milliseconds, else 2 if packet loss is < 5% and round-trip network delay is < 500 milliseconds and jitter compensation delay is < 200 milliseconds, else 1." ::= { endptID 122 } endptRINGTONESKB OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Ring tone file volume. This variable returns The total storage, in KB, currently occupied by ring tone files downloaded via the RINGTONES parameter." ::= { endptID 123 } endptSLMSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "SLA Monitor permission flag. This variable returns 1 if the Avaya Service Level Agreement (SLA)_ Monitor is enabled, else 0." ::= { endptID 124 } endptTUNINGFILE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Audio-tuning status flag. This variable returns 1 if the audio software is currently using information from a downloaded audio tuning file, else 0. " ::= { endptID 125 } endptWARNINGFILE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Warning file permission flag. This variable returns 1 if call recording is currently configured to use a downloaded warning file, else 0." ::= { endptID 126 } endptLOGTOFILE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Flag specifying if optional debug printf strings are logged to an internal file. This variable returns 1 if debug printf strings are logged to an internal file, else 0." ::= { endptID 127 } endptPHY2AUTOMDIXENABLED OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item reflect the value of PHY2_AUTOMDIX_ENABLED configuration parameter. PHY2_AUTOMDIX_ENABLED controls the secondary Ethernet interface Auto MDIX mode (0 for disabled and 1 for enabled (Default)). This variable returns 0 if the endpoint's Secondary Ethernet interface Auto MDIX is currently disabled, 1 if the Secondary Ethernet interface Auto MDIX is currently enabled. " ::= { endptID 128 } endptHWVERSION OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Hardware Version. This variable returns the hardware vintage number." ::= { endptID 129} -- FIPS mode MIB items endptFIPSENABLED OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "FIPS mode. This mib item returns the value of FIPS_ENABLED. If FIPS_ENABLED==1 then only FIPS-approved cryptographic algorithms will be supported and certain list of features will be available for use. By default - FIPS_ENABLED==0." ::= { endptID 140} endptFIPSTEST OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This mib item returns the value of FIPSTEST. If FIPS_ENABLED==0, then FIPSTEST is 0. If FIPS_ENABLED==1, then FIPSTEST is 1 if the self-tests performed by the FIPS-validated cryptographic algorithms passed, else 0 " ::= { endptID 141} -- TLS MIB items endptTLSSRVRVERIFYID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "TLS server ID flag. This MIB item presents the value of TLSSRVRVERIFYID. This variable returns 1 if the TLS server identity is to be checked against its certificate, otherwise 0 (default)." ::= { endptID 150 } endptTLSSECURERENEG OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item presents the value of TLS_SECURE_RENEG. This variable returns 1 if the TLS secure rengeotiation (RFC 5746) is enforced (in this case the TLS connection will be closed if the peer does not support secure renegotiation), otherwise 0 (default)." ::= { endptID 151 } endptTLSVERSION OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item presents the value of TLS_VERSION. This variable returns 0 when TLS 1.0 version and up is supported by the endpoint for all TLS sessions opened by the endpoint and when 1 is returned then TLS 1.2 version and up is supported by the endpoint for all TLS sessions opened by the endpoint." ::= { endptID 152 } -- DSP logs endptAUDIOLOG OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item presents the value of AUDIOLOG which controls whether the DSP logs are collected (1) or not (0, default)" ::= { endptID 161 } endptNVM OBJECT IDENTIFIER ::= {avaya96x1HMIB 2 } endptNVAGCHAND OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Non-Volatile Memory (NVM)Handset AGC status. This variable returns 1 if the endpoint's handset Automatic Gain Control capability in NVM is currently enabled, else 0." ::= { endptNVM 1 } endptNVAGCHEAD OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "NVM Headset AGC status. This variable returns 1 if the endpoint's headset Automatic Gain Control capability in NVM is currently enabled, else 0." ::= { endptNVM 2 } endptNVAGCSPKR OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Speakerphone AGC status. This variable returns 1 if the endpoint's speakerphone Automatic Gain Control capability in NVM is currently enabled, else 0." ::= { endptNVM 3 } endptNVAUTH OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Script file authentication flag. This variable returns 1 if the endpoint must authenticate script files, else 0." ::= { endptNVM 4 } endptNVBRIGHTNESS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display Brightness setting. This variable returns the value of the display contrast setting in non-volatile memory. Range is 0-5, with 4 the default." ::= { endptNVM 5 } endptNVCHADDR OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Manually-entered DHCP chaddr value. This variable returns a manually-entered value for the DHCP chaddr field as stored in non-volatile memory, if any. A Hexadecimal value with range of 0 (the default) to 999999." ::= { endptNVM 6 } endptNVCONTRAST OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display Contrast setting. This variable returns the value of the display contrast setting in non-volatile memory. Range is 0-15, with 8 the default." ::= { endptNVM 7 } endptNVGIPADD OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "NVM Router address. This variable returns a 4-octet string specifying the IP address of the router as stored in NVM." ::= { endptNVM 8 } endptNVIPADD OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "NVM IPv4 address. This variable returns a 4-octet string specifying the endpoint's IPv4 address stored in NVM; all zeroes if no such address is stored." ::= { endptNVM 9 } endptNVIPADDV6 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "NVM IPv6 address. This variable returns a colon-hex string specifying the endpoint's IPv6 address stored in NVM; all zeroes if no such address is stored." ::= { endptNVM 10 } endptNVL2Q OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "NVM 802.1Q flag. This variable returns 0 if the Layer 2 802.1Q framing parameter in NVM is set to 'auto', 1 if it is set to on/enabled, else 2 for off/disabled." ::= { endptNVM 11 } endptNVL2QVLAN OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "NVM VLAN Identifier. This variable returns an integer between 0 and 4094 inclusive specifying the Layer 2 802.1Q VLAN Identifier value stored in NVM." ::= { endptNVM 12 } endptNVLANGFILE OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Language file. This variable returns the name of the language file in non-volatile memory." ::= { endptNVM 13 } endptNVLOGSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "NVM Event Log flag. This variable returns 0 if the endpoint's event logging capability in NVM is currently NOT enabled, else 1." ::= { endptNVM 14 } endptNVNETMASK OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "NVM Subnet mask. This variable returns a 4-octet string specifying the subnet mask as stored in NVM." ::= { endptNVM 15 } endptNVPHY1STAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "NVM Ethernet line interface status. This variable returns 0 if the endpoint's Ethernet line interface in NVM iscurrently NOT enabled, 1 if the Ethernet line interface in NVM is currently for auto-negotiation, 2 for 10Mbps half-duplex, 3 for 10Mbps full-duplex, 4 for 100Mbps half-duplex, and 5 for 100Mbps full-duplex." ::= { endptNVM 16 } endptNVPHY2STAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "NVM Secondary Ethernet interface setting. This variable returns 0 if the endpoint's secondary Ethernet interface in NVM is currently NOT enabled (or none exists), 1 if the hub is set for auto-negotiation, 2 for 10Mbps half-duplex, 3 for 10Mbps full-duplex, 4 for 100Mbps half-duplex, and 5 for 100Mbps full-duplex." ::= { endptNVM 17 } endptNVRINGTONESTYLE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Ringing style identifier. This variable returns the value of RINGTONESTYLE parameter which specifies the style of ring tones that are offered to the user for Personalized Ringing when Classic (as opposed to Rich) is selected. Value Operation 0 North American ring tones are offered (default) 1 European ring tones are offered" ::= { endptNVM 18 } endptNVBM1BRIGHTNESS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Button Module backlight level. This variable returns the value of the backlight brightness for the first Button Module attached to the telephone, if any. Valid values are integers from 1 to 5 inclusive." ::= { endptNVM 19 } endptNVBM2BRIGHTNESS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Button Module backlight level. This variable returns the value of the backlight brightness for the second Button Module attached to the telephone, if any. Valid values are integers from 1 to 5 inclusive." ::= { endptNVM 20 } endptNVBM3BRIGHTNESS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Button Module backlight level. This variable returns the value of the backlight brightness for the third Button Module attached to the telephone, if any. Valid values are integers from 1 to 5 inclusive." ::= { endptNVM 21 } endptNVSSON OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "NVM Site-specific option number. This variable returns an integer between 128 and 254 inclusive, specifying the SSON stored in NVM. The default is 176." ::= { endptNVM 22 } endptNVTRUSTLIST OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "List of trusted certificates. This variable returns 0-255 ASCII characters: 0 or more filenames or URLs separated by commas and without intervening spaces, containing the list of downloaded trusted certificates in non-volatile memory." ::= { endptNVM 23 } endptNVVLANTEST OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "NVM VLAN pause parameter. This variable returns the number of seconds stored in NVM for the endppoint to wait for a DHCPOFFER message when using a non-zero VLAN ID. Valid values are integers from 0 to 999 inclusive." ::= { endptNVM 24 } endptNVVOXFILE OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Voice language file. This variable returns 0-32 ASCII characters: 0 or 1filename, identifying the voice language file, if any, in non-volatile memory." ::= { endptNVM 25 } endptNVMCREGMODE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "H.323 signaling over TLS mode 0 - H.323 signaling over TLS is not allowed. 1 (default) - H.323 signaling over TLS is allowed." ::= { endptNVM 26 } endptH323SIGPROTOCOL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item reflect the value of H323SIGPROTOCOL parameter. H323SIGPROTOCOL defines the security profiles that the endpoint is willing to work with the gatekeeper. 0 - TLS, Annex-H and challenge authentication (default) 1 - TLS and Annex-H 2 - TLS authentication only" ::= { endptNVM 27 } endptMaintenance OBJECT IDENTIFIER ::= { avaya96x1HMIB 3 } endptAPPstat OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Application/Library software package download flag. This variable returns: '0' if the value of APPNAME is null. '1' if the most recent attempt to download a new Application/Library software package was not successful. '2' if the most recent attempt to download a new Application/Library software package was successful, but the file was too large. '3' if the most recent attempt to download a new Application/Library software package was successful, but the file type was incorrect. '4' if the most recent attempt to download a new Application/Library software package was successful, but files were missing, had the wrong file type, or had invalid signatures. '5' if the most recent attempt to download a new Application/Library software package was successful, but was not valid for the telephone hardware. '6' if the most recent attempt to download a new Application/Library software package was successful, but it was not compatible with the new Kernel/RFS software package. '7' if the most recent attempt to download a new Application/Library software package was successful, but it was not compatible with the existing Kernel/RFS software package. '8' if the most recent attempt to download a new Application/Library software package was successful, but the existing Kernel/RFS software package was not compatible with it. '9' if the most recent attempt to download, store and install a new Application/Library software package was successful. '10' if there was a failure to write software file to flash (Supported by phones with HWVERS 3 and up as conveyed by endptHWVER). '11' if there was a failure of signature verification for BootA (Supported by phones with HWVERS 3 and up as conveyed by endptHWVER). '12' if there was a failure of signature verification for BootB (Supported by phones with HWVERS 3 and up as conveyed by endptHWVER).; '13' if there was a failure of signature verification for system RFS (Supported by phones with HWVERS 3 and up as conveyed by endptHWVER). '14' if a new firmware file was found to have the same software version as the one installed (identical software) - no upgrade required (Supported by phones with HWVERS 3 and up as conveyed by endptHWVER)." ::= { endptMaintenance 1 } endptUPGRADESTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Script loading status flag. This variable returns '0' if an upgrade.txt file was successfully obtained and interpreted since the last power-up or reset. This variable returns '1' if the file was successfully obtained but NOT successfully interpreted since the last power-up or reset. This variable returns '2' if the file was NOT successfully obtained since the lastpower-up or reset." ::= { endptMaintenance 2 } endptRecentLog OBJECT-TYPE SYNTAX SEQUENCE OF EndptRecentLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is one of up to 500 syslog event messages added since last reset or power-up, each of which has severity code less than the value of NVLOGLOCAL. Entries are in chronological order, oldest first." ::= { endptMaintenance 3 } endptRecentLogEntry OBJECT-TYPE SYNTAX EndptRecentLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is one of up to 500 syslog event messages added since last reset or power-up, each of which has severity code less than the value of NVLOGLOCAL. Entries are in chronological order, oldest first." INDEX { endptRecentLogText } ::= { endptRecentLog 1 } EndptRecentLogEntry ::= SEQUENCE { endptRecentLogText DisplayString } endptRecentLogText OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Syslog event message." ::= { endptRecentLogEntry 1 } endptResetLog OBJECT-TYPE SYNTAX SEQUENCE OF EndptResetLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is one of up to 500 syslog event messages added before the last reset or power-up, each of which has severity code less than the value of NVLOGLOCAL. Entries are in chronological order, oldest first." ::= { endptMaintenance 4 } endptResetLogEntry OBJECT-TYPE SYNTAX EndptResetLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is one of up to 500 syslog event messages added before the last reset or power-up, each of which has severity code less than the value of NVLOGLOCAL. Entries are in chronological order, oldest first." INDEX { endptResetLogText } ::= { endptResetLog 1 } EndptResetLogEntry ::= SEQUENCE { endptResetLogText DisplayString } endptResetLogText OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Syslog event message." ::= { endptResetLogEntry 1 } endptRFSStat OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Boot file loading status flag. This variable returns '0' if the value of RFSNAME is null; '1' if the most recent attempt to download a new Kernel/RFS software package was not successful; '2' if the most recent attempt to download a new Kernel/RFS software package was successful, but the file was too large; '3' if the most recent attempt to download a new Kernel/RFS software package was successful, but the file type was incorrect; '4' if the most recent attempt to download a new Kernel/RFS software package was successful, but files were missing, had the wrong file type, or had invalid signatures; 5' if the most recent attempt to download a new Kernel/RFS software package was successful, but was not valid for the telephone hardware; '6' if the most recent attempt to download a new Kernel/RFS software package was successful, but it was not compatible with the new Application/Library software package; '7' if the most recent attempt to download a new Kernel/RFS software package was successful, but it was not compatible with the existing Application/Library software package; '8' if the most recent attempt to download a new Kernel/RFS software package was successful, but the existing Application/Library software package was not compatible with it; or '9' if the most recent attempt to download a new compatible Kernel/RFS software package was successful. This MIB item is not applicable for phones with HWVERS 3 and up as conveyed by endptHWVER." ::= { endptMaintenance 5 } endptStartupLog OBJECT-TYPE SYNTAX SEQUENCE OF EndptStartupLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is one of up to the first 75 syslog event messages added since last reset or power-up, each of which has severity code less than the value of NVLOGLOCAL. Entries are in chronological order, oldest first." ::= { endptMaintenance 6 } endptStartupLogEntry OBJECT-TYPE SYNTAX EndptStartupLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is one of up to the first 75 syslog event messages added since last reset or power-up, each of which has severity code less than the value of NVLOGLOCAL. Entries are in chronological order, oldest first." INDEX { endptStartupLogText } ::= { endptStartupLog 1 } EndptStartupLogEntry ::= SEQUENCE { endptStartupLogText DisplayString } endptStartupLogText OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Syslog event message." ::= { endptStartupLogEntry 1 } endptSSHSTATUS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Secure Shell status flag. This variable returns '0' if SSH is disabled;'1' if is enabled but inactive; and '2' if SSH is active." ::= { endptMaintenance 7 } endptAUTHCTRLSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Enhanced debugging capabilities mode. This MIB item reflects the value of AUTHCTRLSTAT. If 0 (default), then the enhanced debugging capabilities mode is disabled. if 1, then the enhanced debugging capabilities mode is enabled. This mode shall ALWAYS be disabled, unless Avaya Technician requests to enable it for better debugging of the phone." ::= { endptMaintenance 10 } endptApps OBJECT IDENTIFIER ::= { avaya96x1HMIB 4 } endptAPPSTATVALUE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Applications permission status. This variable returns the current value of the APPSTAT parameter, which can restrict the availability of some of the telephone applications, as documented in the 9600 Series Admin Guide." ::= { endptApps 1 } endptAUDIOPATH OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "User audio path. This variable returns 0 if the telephone does not support a 2-way speaker or does not have a headset jack; 1 if the user audio path is with the speakerphone, and 2 if the user audio path is with the headset." ::= { endptApps 2 } endptCLDELCALLBK OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Call Log Callback Deletion flag. This variable returns 1 if a Missed Call Log entry is deleted from the Call Log if the user Calls that entry from the Call Log, else 0 (the default) ." ::= { endptApps 3} endptENHDIALSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Enhanced Local Dialing status. This variable returns 0 if the Enhanced Local Dialing status is off/disabled, else 1 if enabled for all applications except contact application or 2 if enabled for all applications." ::= { endptApps 4 } endptFBONCASCREEN OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Feature Buttons on Call Appearance List flag. This variable returns 1 if administered feature buttons are allowed to be listed on the Call Appearance Screen, else 0 (the default) ." ::= { endptApps 5 } endptGUESTDURATION OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "96x1 Guest Login Duration. This variable returns an integer specifying the number of hours from 1-12 for the Guest Login duration. The default is 2." ::= { endptApps 6 } endptGUESTLOGINSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "96x1 Guest Login permission flag. This variable returns 1 if the user is allowed to initiate a Guest Login, otherwise 0." ::= { endptApps 7 } endptGUESTWARNING OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "96x1 Guest Login Warning interval. This variable returns an integer specifying the number of minutes from 1-15 before the expiration of a Guest Login that a warnign screen is displayed. The default is 5." ::= { endptApps 8 } endptLOGBACKUP OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Call Log backup permission flag. This variable returns 1 (the default) if the telephone is to automatically store and retrieve a file of Call Log entries, else 0." ::= { endptApps 9 } endptLOGMISSEDONCE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Missed Call Log Counter flag. This variable returns 1 if the telephone keeps only one Missed Call Log record for a given Name and Number, as well as a counter of Missed calls from that Name and Number, else 0 (the default)." ::= { endptApps 10 } endptLOGUNSEEN OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Log redirected calls permission flag. This variable returns 1 if the telephone is to create Call Log entries for calls that are redirected from the physical telephone, else 0 (the default)." ::= { endptApps 11 } endptOPSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Options permission status. This variable returns the current value of the OPSTAT parameter, which can restrict the availability of some of the telephone options, as documented in the Admin Guide." ::= { endptApps 12 } endptOPSTAT2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Options permission override parameter. This variable returns the current value of the OPSTAT2 parameter, which can override specific functionality of the OPSTAT parameter, as documented in the Admin Guide." ::= { endptApps 13 } endptPUSHCAP OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Push capabilities. This variable returns a 4-digit integer specifying the phone administration for audio transmit, audi receive, display (web), and Top Line pushes, respectively. The valid digits are 0 (Disabled), 1 (barge-in onl ypushes of the given type Enabled) and 2 (both barge-in and normal pushes of the given type Enabled). The default is 2222." ::= { endptApps 14 } endptPUSHPORT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Push listening port. This variable returns an integer specifying the TCP listening port most recently used for the HTTP server.." ::= { endptApps 15 } endptQKLOGINSTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Quick Login permission flag. This variable returns 1 (the default) if users are permitted to use the # button to use a previous login and password during registration, else 0." ::= { endptApps 16 } endptSCREENSAVER OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Custom screen saver URL. This variable returns a filename from 0-32 characters that specifies an image displayed in lieu of the Avaya screen saver." ::= {endptApps 17 } endptSUBSCRIBELIST OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "96x1 Web push subscription list. This variable returns a string containing one or more fully qualified URLs to which the phone's Browser application subscribes for potential pushed content." ::= { endptApps 18 } endptTPSLIST OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "96x1 Web Trusted Push Server list. This variable returns a string containing one or more domains and paths in DNS format, used to determine for validation of push requests." ::= { endptApps 19 } endptWMLEXCEPT OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "96x1 Web Proxy Server Exception List. This variable returns a string specifying a list of one or more HTTP proxy server Exception domains, separated by commas with no intervening spaces, up to 127 total characters. Used by the 96x1 Browser application." ::= { endptApps 20 } endptWMLHOME OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "96x1 Web application URL. This variable returns a URL of the Home page for the 96x1 Browser application." ::= { endptApps 21 } endptWMLIDLETIME OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Web Idle Timer. This variable returns the number of minutes, from 1 to 60 inclusive, of idle activity on the telephone before the Web Idle Timer URI is displayed." ::= { endptApps 22 } endptWMLIDLEURI OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Web Idle Timer URI. This variable returns the URI of the WML page displayed after the 96x1 Web Idle Timer expires." ::= { endptApps 23 } endptWMLPORT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "96x1 Browser application TCP port. This variable returns an integer specifying the TCP port most recently used for the HTTP proxy server. Used by the 96x1 Browser application." ::= { endptApps 24 } endptWMLPROXY OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "96x1 Web Proxy Server. This variable returns an IP address, in dotted-decimal, colon-hex, or DNS format, converted to a text string, of an HTTP proxy server. Used by the 96x1 Browser application." ::= { endptApps 25 } endptCTASTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Call Type Analysis feature status. Return the value of CTASTAT configuration parameter. If value is 1, then the endpoint uses Avaya Communication Manager Call Type Analysis feature (if enabled) for all applications (such as History, redial, WML browser, etc) with exception to contact application. If value is 2, then the endpoint uses Avaya Communication Manager Call Type Analysis (if enabled) for all applications including contact application " ::= { endptApps 26 } endptCLBACKUPTIMESTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Enable periodic backup of the call log data to backup/restore server. The variable returns the current value CLBACKUPTIMESTAT set to settings file 0 if the parameter is not set (default)." ::= { endptApps 27} endptCLBACKUPTIME OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Call log backup timer duration. This variable returns current value set in the CLBACKUPTIME set in the settings file." ::= { endptApps 28} endptCLDISPCONTENT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Call Log Display parameter. Returns the current value of the CLDISPCONTENT parameter from 0 to 2" ::= { endptApps 29} endptCLEAR_EXTPSWD_ON_LOGOUT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "CLEAR_EXTPSWD_ON_LOGOUT flag. This variable returns 1 if the extension and password are cleared on Logout." ::= { endptApps 30} endptAdjuncts OBJECT IDENTIFIER ::= { avaya96x1HMIB 5 } endptBMODS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Button Module interface usage. This variable returns the number of devicess attached (or daisy-chained) to the endpoint through the button module interface." ::= { endptAdjuncts 1} endptBM1HWVER OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Button Modile hardware version. This variable returns the hardware version of the first button module attached, if any. If none, null is returned." ::= {endptAdjuncts 2} endptBM1SWVER OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Button Modile software version. This variable returns the software version of the first button module attached, if any. If none, null is returned." ::= {endptAdjuncts 3} endptBM2HWVER OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Button Modile hardware version. This variable returns the hardware version of the second button module attached, if any. If none, null is returned." ::= { endptAdjuncts 4} endptBM2SWVER OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Button Modile software version. This variable returns the software version of the second button module attached, if any. If none, null is returned." ::= {endptAdjuncts 5} endptBM3HWVER OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Button Modile hardware version. This variable returns the hardware version of the third button module attached, if any. If none, null is returned." ::= {endptAdjuncts 6} endptBM3SWVER OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Button Modile software version. This variable returns the software version of the third button module attached, if any. If none, null is returned." ::= {endptAdjuncts 7} endptUSBPOWER OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "USB Power Provision. This variable returns 0 if the telephone is to disable USB power, 1 if USB power is enabled only if the telephone is Aux powered, 2 if USB power is enabled regardless of the power source, or 3 if USB power is enabled if the telephone is Aux powered or PoE Class 3." ::= { endptAdjuncts 8 } endptASPCONNECT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Adjunct Speakerphone status. This variable returns 0 if an adjunct speakerphone is not known to be connected or paired, 1 if an adjunct speakerphone is connected via the adjunct interface, 2 if an adjunct speakerphone is paired via Bluetooth, and 3 if an adjunct speakerphone is connected via USB." ::= { endptAdjuncts 9 } endptASPHWVER OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Adjunct Speakerphone hardware version. This variable returns the hardware version of the adjunct Speakerphone known to be connected or paired, if any. If none, null is returned." ::= {endptAdjuncts 10} endptASPSWVER OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Adjunct Speakerphone software version. This variable returns the software version of the adjunct Speakerphone known to be connected or paired, if any. If none, null is returned." ::= {endptAdjuncts 11} endptH323 OBJECT IDENTIFIER ::= { avaya96x1HMIB 6 } endptGKINUSE OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Gatekeeper in use address. This variable returns a 4-octet string specifying the IP address of the gatekeeper currently in use." ::= { endptH323 1 } endptGKTCPPORT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Gatekeeper Port. This variable returns 0 if the telephone is not currently registered, otherwise it returns the TCP port number on the gatekeeper with which the telephone has a signaling connection established." ::= { endptH323 2 } endptMCIPADD OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "List of call server addresses. This variable returns a sequence of IP addresses, in dotted-decimal, colon-hex, or DNS format and separated by commas, of call server IP addresses available for use." ::= { endptH323 3 } endptNVPHONEXT OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Endpoint's phone extension. This variable returns a text string identifying the endpoint's extension, in free text format. The default value is NULL. " ::= { endptH323 4 } endptRASGkList OBJECT-TYPE SYNTAX SEQUENCE OF EndptRASGkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is one of up to 75 gatekeeper addresses in dotted-decimal, colon-hex, or DNS format, as downloaded from the call server during RAS. Entries are listed in the order received." ::= { endptH323 5 } endptRASGkEntry OBJECT-TYPE SYNTAX EndptRASGkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is one of up to 75 gatekeeper addresses in dotted-decimal or DNS format, as downloaded from the call server during RAS. Entries are listed in the order received." INDEX { endptRASGkEntryData} ::= { endptRASGkList 1 } EndptRASGkEntry ::= SEQUENCE { endptRASGkEntryData DisplayString } endptRASGkEntryData OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Data for an individual RAS-provided Gatekeeper." ::= { endptRASGkEntry 1 } endptREREGISTER OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Reregistration Timer value. This variable returns the number of minutes from 1 to 120 inclusive the telephone waits between re-registration attempts if unnamed registration is not in effect. The default is 20 minutes." ::= { endptH323 6 } endptSERVICESTAT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Status of phone in service. This variable returns: 0 if the phone is not in service nor is attempting to register 1 if the telephone has failed Gatekeeper Discovery 2 if the telephone has successfully completed Gatekeeper Discovery but has not successfully completed registration. In case of signaling over TCP, TCP connection is not established yet. In case of signaling over TLS, TLS connection may or may not established in this phase. 3 if the telephone has successfully registered, no signaling. In case of TCP, the phone does not have a TCP connection with ACP yet, but in case of TLS, the phone has TLS connection established. 4 phone is registered and has a TCP/TLS connection with ACP (signaling channel established)" ::= { endptH323 7 } endptCERT OBJECT IDENTIFIER ::= { avaya96x1HMIB 8 } endptMYCERTCAID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Certificate Authority ID. This variable returns the Certificate Authority Identifier to be used in a certificate request." ::= { endptCERT 1 } endptMYCERTCN OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Certificate Common Name. This variable returns the Common Name of the Subject of a certificate request." ::= { endptCERT 2 } endptMYCERTDN OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Certificate Distinguished Name. This variable returns additional information (sometimes common country and organizational information) that, together with the Common Name, is used to create a Distinguished Name." ::= { endptCERT 3 } endptMYCERTKEYLEN OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Key length. This variable returns the bit length of the public and private keys generated for a certificate request" ::= { endptCERT 4 } endptMYCERTRENEW OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Certificate Renewal interval. This variable returns the percentage of a certificate Validity interval after which renewal procedures will be initiated." ::= { endptCERT 5 } endptMYCERTURL OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "SCEP URL. This variable returns the URL to be used to contact an SCEP server." ::= { endptCERT 6 } endptMYCERTWAIT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Certificate wait flag. This variable returns 0 if the telephone will wait until a pending certificate request is complete, else 1 if it will periodically check in the background." ::= { endptCERT 7 } endptCertLifeRemaining OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Certificate life remaining. This variable returns the integer percentage remaining of the time interval specified in the Validity object for the device certificate." ::= { endptCERT 8 } endptCertPollRetries OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Certificate retry counter. This variable returns the The number of times the telephone has tried to contact MYCERTURL to check on the status of a pending certificate request." ::= { endptCERT 9 } endptCertReqPending OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Certificate request pending flag. This variable returns 1 if a certificate request is pending, else 0. " ::= { endptCERT 10 } endptMYCERTKEYUSAGE OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Certyificate usage list. This variable returns the list of purpose(s) for which a certificate is issued." ::= { endptCERT 11 } endptSCEPPASSWORDREQ OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "SCEP challenge flag. This variable returns 1 if the the user is to be prompted to enter an SCEP challenge password when applicable, else 0." ::= { endptCERT 12 } -- PKCS#12 MIB items endptPKCS12URL OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item returns PKCS12URL which specifies the URL used to download a PKCS #12 file containing an identity certificate and its private key. By default null string." ::= { endptCERT 20 } -- OCSP MIB items endptOCSPENABLED OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item returns OCSP_ENABLED which specifies whether OCSP will be used to check the revocation status of certificates. If OCSP_ENABLED==1 then OCSP will be used to check the revocation status of server certificates (including all certificates in chain except root certificate) else if OCSP_ENABLED==0 (default) OCSP will not be used." ::= { endptCERT 30 } endptOCSPURI OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item returns OCSP_URI which specifies URI for an OCSP responder. By default null string." ::= { endptCERT 31 } endptOCSPURIPREF OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item returns OCSP_URI_PREF which specifies the preferred URI to use for OCSP requests if OCSPURI is configured and Authority Information Access (AIA) extension of the certificate being checked has valid value. If the value is 1 (default) then the preference is for OCSPURI and then Authority Information Access (AIA) extension of the certificate being checked. If the value is 2 then the preference is for Authority Information Access (AIA) extension of the certificate being checked and then OCSPURI." ::= { endptCERT 32 } endptOCSPACCEPTUNK OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item returns OCSP_ACCEPT_UNK which specifies whether a certificate will be authenticated even if its status cannot be determined. If OCSP_ACCEPT_UNK==1 (default) then certificates that their revocation status is uknown will be accepted. If OCSP_ACCEPT_UNK==0 then certificates that their revocation status is uknown will not be accepted and TLS connection will be closed." ::= { endptCERT 33 } endptOCSPNONCE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item returns OCSP_NONCE which specifies whether a nonce will be included in OCSP requests and expected in OCSP responses. If OCSP_NONCE==1, then OCSP responses shall have the same nonce as in the OCSP requests else the OCSP response is ignored. If OCSP_NONCE==0 (default), then OCSP nonce is not included in the OCSP requests and not checked in the OCSP responses." ::= { endptCERT 34 } endptOCSPTRUSTCERTS OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item returns OCSP_TRUSTCERTS which specifies a list of files to be downloaded as a separate trusted certificate repository for the OCSP Trusted Responder Model that contains certificates to be trusted from OCSP responders when the OCSP response is not signed by a certificate issued by the same CA that issued the certificate that is being checked. By default, null string." ::= { endptCERT 35 } endptOCSPTRUSTLIST OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item returns OCSP_TRUSTLIST which specifies the list of files that were downloaded as a separate trusted certificate repository for the OCSP Trusted Responder Model that contains certificates to be trusted from OCSP responders when the OCSP response is not signed by a certificate issued by the same CA that issued the certificate that is being checked. By default, null string." ::= { endptCERT 36 } -- Certificate expiration and revocation endptCERTWARNINGDAYS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Thib MIB item presents the value of CERT_WARNING_DAYS (default 60 days) which used to specify the number of days before expiration of identity certificate, trusted certificate or OCSP certificate at which a warning should first be displayed and a syslog/log should first be sent/generated." ::= { endptCERT 40 } endptSERVERCERTRECHECKHOURS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This MIB item returns SERVER_CERT_RECHECK_HOURS which specifies the number of hours after which certificate expiration and OCSP will be used (if OCSP is enabled) to recheck the revocation and expiration status of the certificates that were used to establish on going TLS connection. A value of 0 means that periodic checks will not be done (default is 24 hours)." ::= { endptCERT 41 } endptVPN OBJECT IDENTIFIER ::= { avaya96x1HMIB 9 } endptALWCLRNOTIFY OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "ISAKP Notification flag. This variable returns 1 if unencrypted ISAKMP Notification Payloads will be accepted, else 0." ::= { endptVPN 1 } endptAUTHTYPE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VPN Authentication Method. This variable returns 3 if the VPN authentication method is Pre-Shared Key (PSK); 4 if the method is PSK with XAUTH, 5 if the method is RSA signatures with XAUTH, 6 if the method is Hybrid XAUTH, and 7 if the method is RSA signatures." ::= { endptVPN 2 } endptCFGPROF OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VPN Configuration Profile. This variable returns 2 if the VPN Configuration Profile is based on Checkpoint Security Gateway, 3 if the profile is based on Cisco PSK with XAUTH, 5 if the profile is based on Juniper PSK with XAUTH, 6 if the profile is based on Generic PSK, 8 if the profile is based on Cisco Cert. with XAUTH, 9 if the profile is based on Juniper Cert. with XAUTH, or 11 if the profile is based on Nortel Contivity." ::= { endptVPN 3 } endptCOPYTOS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "TOS Copy flag. This variable returns 1 if the value of the TOS bits will be copied from the inner IP header to the outer IP header, else this variable returns 2 and the TOS bits of the outer IP header will be set to 0." ::= { endptVPN 4 } endptDHCPSRVR OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "List of DHCP server addresses. This variable returns a sequence of zero or more IP addresses, in dotted-decimal format and separated by commas, of enterprise DHCP servers from which configuration parameters may be requested through a VPN tunnel via a DHCPINFORM message." ::= { endptVPN 5 } endptDROPCLEAR OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Clear IPSec packet treatment. This variable returns 1 if received unencrypted (clear) IPsec packets are to be dropped, else 0" ::= { endptVPN 6 } endptENCAPS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Encapsulation Port Numbers. This variable returns 0 if negotiation of NAT traversal is as specified in IETF RFC 3947 (except that IKE negotiation begins with a source port of 2070 and that source port continues to be used unless the source and destination port numbers are changed to 4500, 1 if UDP encapsulation of the inner IP layer will not be provided and negotiation of NAT traversal as specified in IETF RFC 3947 is not supported, 2 if negotiation of NAT traversal is as specified in IETF RFC 3947 (except IKE uses source port 2070 and the source and destination port numbers are not subsequently changed), or 4 if negotiation of NAT traversal is as specified in IETF RFC 3947." ::= { endptVPN 7 } endptEXTDNSSRVR OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "List of external DNS server addresses. This variable returns a sequence of IP addresses, in dotted-decimal format and separated by commas, of DNS servers available for use outside of the VPN tunnel when in VPN mode." ::= { endptVPN 8 } endptEXTGIPADD OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "List of external router addresses. This variable returns a sequence of IP addresses, in dotted-decimal format and separated by commas, of routers available for use outside of the VPN tunnel when in VPN mode." ::= { endptVPN 9 } endptEXTIPADD OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Endpoint External IP address. This variable returns a 4-octet string specifying the endpoint's current outer IP address when in VPN mode." ::= { endptVPN 10 } endptEXTNETMASK OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "External Subnet mask. This variable returns a 4-octet string specifying the subnet mask to be used outside of the VPN tunnel when in VPN mode." ::= { endptVPN 11 } endptIKECONFIGMODE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "IKE Configuration flag. This variable returns 1 if the ISAKMP configuration method to be used, else 2.." ::= { endptVPN 12 } endptIKEDH OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "In-Use Diffie-Hellman Group for IKE SA. This variable returns the negotiated IKE Phase 1 DH Group number." ::= { endptVPN 13 } endptIKEDHGRP OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Proposed Diffie-Hellman Group for IKE SA. This variable returns 1 if the DH Group Description proposed for IKE Phase 1 is the First Oakley Group, 2 if the proposal is for the Second Oakley Group, 5 if the proposal is for the 1536-bit MODP Group, 14 if the proposal is for the 2048-bit MODP Group, and 15 if the proposal is for the 3072-bit MODP Group, else 0." ::= { endptVPN 14 } endptIKEID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "IKE Phase 1 identity, This variable returns the identity (also known as in XAUTH as group name) used during IKE Phase 1 negotiation." ::= { endptVPN 15 } endptIKEIDTYPE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "IKE SA identification type. This varable returns 1 if the Identification Type used for IKE Phase 1 is ID_IPV4_ADDR, 2 if the ID Type is ID_FQDN, 3 if the ID Type is ID_USER_FQDN, 9 if the ID Type is ID_DER_ASN1_DN, and 11 if the ID Type is ID_KEY_ID." ::= { endptVPN 16 } endptIKEOVERTCP OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "IKE TCP usage policy. This variable returns 0 if IKE is only to use UDP, 1 if TCP is to be tried after an IKE times out using UDP, or 2 if only TCP is to be used." ::= { endptVPN 17 } endptIKEP1AUTH OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "In-Use IKE Phase 1 authentication algorithm. This variable returns 1 if MD5 was negotiated, and 2 if SHA was negotiated." ::= { endptVPN 18 } endptIKEP1AUTHALG OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Proposed IKE Phase 1 authentication algorithm. This variable returns 0 if if either hash algorithm is acceptable for IKE Phase 1, 1 if MD5 is proposed, or 2 if SHA is proposed:." ::= { endptVPN 19 } endptIKEP1ENC OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "In-Use IKE Phase 1 encryption algorithm. This variable returns 1 if AES-CBC-128 was negotiated, 2 if 3DES-CBC was negotiated, 3 if DES-CBC was negotiated, 4 if AES-CBC-192 was negotiated, or 5 if AES-CBC-256 was negotiated." ::= { endptVPN 20 } endptIKEP1ENCALG OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "IKE Phase 1 encryption algorithm. This variable returns.0 if any encryption algoithm is acceptable for IKE Phase 1, 1 if AES-CBC-128 is proposed, 2 if 3DES-CBC is proposed, 3 if DES-CBC is proposed, 4 if AES-CBC-192 is proposed, and 5 if AES-CBC-256 is proposed." ::= { endptVPN 21 } endptIKEP1LIFESEC OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "IKE Security Association lifetime. This variable returns the proposed number of seconds for the SA Life Duration for IKE Phase 1." ::= { endptVPN 22 } endptIKEP2AUTH OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "In-Use IKE Phase 2 authentication algorithm. This variable returns 1 if MD5 was negotiated, and 2 if SHA was negotiated." ::= { endptVPN 23 } endptIKEP2AUTHALG OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "IKE Phase 2 authentication algorithm. This variable returns 0 if either hash algorithm is acceptable for IKE Phase 1, 1 if MD5 is proposed, or 2 if SHA is proposed:." ::= { endptVPN 24 } endptIKEP2ENC OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "In-Use IKE Phase 2 encryption algorithm. This variable returns 1 if AES-CBC-128 was negotiated, 2 if 3DES-CBC was negotiated, 3 if DES-CBC was negotiated, 4 if AES-CBC-192 was negotiated, 5 if AES-CBC-256 was negotiated, or 6 if NULL encryption was negotiated." ::= { endptVPN 25 } endptIKEP2ENCALG OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "IKE Phase 1 encryption algorithm. This variable returns.0 if any encryption algoithm is acceptable for IKE Phase 1, 1 if AES-CBC-128 is proposed, 2 if 3DES-CBC is proposed, 3 if DES-CBC is proposed, 4 if AES-CBC-192 is proposed, 5 if AES-CBC-256 is proposed, and 6 if NULLencryption is proposed." ::= { endptVPN 26 } endptIKEP2LIFESEC OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "IPsec Security Association lifetime. This variable returns the proposed number of seconds for the SA Life Duration for IKE Phase 2." ::= { endptVPN 27 } endptIKESALIFEKB OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "IKE Security Association KB Lifetime. This variable returns the IKE SA lifetime in kilobytes." ::= { endptVPN 28 } endptIKESALIFESEC OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "IKE Security Association time Lifetime. This variable returns the IKE SA lifetime in seconds." ::= { endptVPN 29 } endptIKETRANSPORT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "In-Use IKE transport protocol. This variable returns 0 if IKE is not in use, 1 if UDP is being used for IKE transport, or 2 if TCP is being used for IKE transport." ::= { endptVPN 30 } endptIKEXCHGMODE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "IKE Phase 1 negotiation mode. This variable returns 1 if the IKE Phase 1 exchange usesd is Aggressive Mode, else 2 for Main Mode. " ::= { endptVPN 31 } endptIPSECSALIFEKB OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "IPsec Security Association KB Lifetime. This variable returns the IPsec SA lifetime in kilobytes." ::= { endptVPN 32 } endptIPSECSALIFESEC OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "IPsec Security Association time Lifetime. This variable returns the IPsec SA lifetime in seconds." ::= { endptVPN 33 } endptIPSECSUBNET OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VPN Tunnel IP Address ranges. This variable returns the IP address ranges that will use the VPN tunnel, with 0.0.0.0/0 meaning all IP addresses." ::= { endptVPN 34 } endptNORTELAUTH OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Nortel gateway authentication method. If Nortel gateway user authentication is to be used, this variable returns 1 if a local username and password are to be used; 2 if a RADIUS username and password are to be used, 3 if RADIUS SecurID is to be used, and 4 if RADIUS Axent is to be used.." ::= { endptVPN 35 } endptPFSDH OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "In-Use Diffie-Hellman Group for IPsec SA. This variable returns the negotiated IKE PFS DH Group number." ::= { endptVPN 36 } endptPFSDHGRP OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Diffie-Hellman Group for IPsec SA. This variable returns 1 if the DH Group Description proposed for IPSec SA is the First Oakley Group, 2 if the proposal is for the Second Oakley Group, 5 if the proposal is for the 1536-bit MODP Group, 14 if the proposal is for the 2048-bit MODP Group, and 15 if the proposal is for the 3072-bit MODP Group, else 0." ::= { endptVPN 37 } endptPSWDTYPE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VPN Password Permissions. This variable returns 1 if the password may be alphanumeric and is to be stored in non-volatile memory as the value of NVVPNPSWD, 2 if the password may be alphanumeric and is to be stored in volatile memory that will be cleared when the telephone resets, 3 if the password may be numeric-only and is to be stored in volatile memory that will be cleared mmediately after the first time the password is used (this is for use with numeric-only one-time token devices), 4 if the password may be alphanumeric and is to be stored in volatile memory that will be cleared immediately after the first time the password is used, and 5 if the password may be alphanumeric and is to be stored in volatile memory that is cleared when the user invokes VPN Sleep Mode and when the telephone resets." ::= { endptVPN 38 } endptSGINUSE OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VPN Security Gateway address. This variable returns a 4-octet string specifying the IP address of the VPN Security Gateway in use, else 0.0.0.0." ::= { endptVPN 39 } endptSGIP OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VPN Security Gateway list. This variable returns the list of VPN security gateway IP addresses available to the telephone." ::= { endptVPN 40} endptSGVENDOR OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VPN Security Gateway Vendor. This variable returns 1 if the IKE implementation matches Juniper/NetScreen, 2 if it matches Cisco, 3 if it matches Check Point/Nokia, 5 if it matches Nortel, otherwise 4." ::= { endptVPN 41 } endptSGVERSION OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Security Gateway Version. This variable returns the version information, if any, of the Security Gateway with wich the telephone has a VPN tunnel established, else NULL." ::= { endptVPN 42 } endptVPNMODE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VPN Support Specification. This variable returns 1 if VPN functionality is enabled, else 0." ::= { endptVPN 43 } endptVPNUSER OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VPN User Name. This variable returns the user name to be used during authentication. " ::= { endptVPN 44 } endptVPNUSERTYPE OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VPN User Name Permissions. This variable returns 1 if the user can change the VPN username, else 0." ::= { endptVPN 45 } endptXAUTH OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "XAUTH status. This variable returns 2 if XAUTH is disabled, else 1." ::= { endptVPN 46 } endptVPNTOKENINPUT OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Token prompt status. This variable r Specifies whether a separate prompt will be displayed for entry of a VPN Password or a Token PIN in addition to the Token Code, and the order in which the values will be concatenated for VPN authentication. See the Admin Guide for more detail." ::= { endptVPN 47 } END